Cust0mer Reviews
What our customers say
Previous
Next
Lethal Weapon 3 Gun Launcher conversion
1. Turn machine off and unplug it.
2. Unplug the connector for the micro switch to the current gun. (Photo 1)
3. Unplug bolt the 6 bolts that hold the gun to the cabinet (photo2)
4. Remove microswitch bracket from machine cabinet (photo3)
5. Remove micro switch from microswitch bracket. Make note of what wire goes where on the switch. Remove micro switch screws and retain black plate (Photo 10)
6. Drill a 3/4 inch hole into your cabinet where the gun mount center bolts are located. Right in the center. (Photo 4)
7. Cut off and. Modify microswitch connector on the bottom so that you can still solder a wire to it. (Photo 5)
8. On the pig tail harness you have to cut the plug end off at about 1.5 inch away from the plug so that you still have enough wire to solder back tougher.
9. Cut the green single wire connector off. Strip the wire and soldier it onto the cut off post on the micro switch. White wire will stay connected to switch.
10. Twist pig tail wires and feed through gun mount hole in the handle. (Photo 6)
11. Position the switch and set it in the center of the gun mount. You will need to wedge this piece in. I used cut prices of a zip tie to wedged it in so it does not shift. (Photo 7)
12. On the gun mount cover where the trigger mounts the two shallow holes for the trigger need to be wider, I did this by using a 3/16 drill bit and turning it by hand till enough plastic came off. Dont use a drill or you will drill right threw it. (Photo 8)
13. Place trigger and gun mount into the gun body. Assemble both halves and check the operation of the trigger. You will need to make minor adjustments/fitness it at this step to get it all to fit and work correctly.
14 soldier back on the pig tail end. (Photo9)
15 reattach gun and mount to cabinet, plug pig tail in and test. (Photo 11)
Looks so freaking cool Love this
- fnosmGreat mod! I highly recommend this one. As of the date of this review, I think this is the best Death Eater Airball protector available. I had another one but ... Read More
- Jam_BurglarThis is a good mod- looks like the train should had been there from the factory! There are two tracks you can get (if you want to include the passenger ... Read More
- BSoulManThe Pinboots accentuate the CE nicely... Nice and relatively inexpensive mod!
- BSoulManSimple products, easy install, nice peace of mind that doesn’t interfere with ball travel.
- HarvesterInstalled the variant with “Death Eater”; built like a tank and going strong after 3 weeks and dozens of games.
- HarvesterNice product. Fine feet faster seem solid, colors are great, and fit just right
- MinusWorldsShould have been stock for home use. I get that operators may love a fat left drain to keep game income higher, but nimr0d's left lane fix is the best ... Read More
- PintermissionHad another protector there before. It broke after a few plays. This one is robust and will probably outlast the pin itself!
- bjorgFrankly, this is how the game should have looked from the get go. Super easy to install. Just cut the adhesive into small strips. Two screws to undo for the ... Read More
- bjorgLove it. Looks like it should have been there from the get go. I found it easier to loosen the screws behind the backboard and remove the mirror with its ... Read More
- bjorgThe PinBoots match EXACTLY the color of the golden legs on the CE. It looks amazing! Highly recommended to pair with black leg levelers unless you can find golden ones. ... Read More
- bjorgYeah, this is so obvious. It should have been installed at the factory. Don't hesitate to buy! Every machine should have it.
- bjorgThis thing is pretty awesome! Lots of a attention to detail! It is larger than my other pincups, but not much larger. You won't be disappointed!
- DippinMyToeInEasy and worthwhile mod. Should have been this way from the factory. A must for any HP pin.
- DippinMyToeIn fnosm
fnosm Looks so freaking cool Love this
Jam_Burglar Jam_Burglar Great mod! I highly recommend this one. As of the date of this review, I think this is the best Death Eater Airball protector available. I had another one but it shattered very quickly because brittle plastic just can't take the abuse this area gets. The ABS plastic used on this protector, on the other hand, has held up like a champ. My only suggestion would be to do a third design option: a plain
black version without any writing at all.
BSoulMan BSoulMan This is a good mod- looks like the train should had been there from the factory! There are two tracks you can get (if you want to include the passenger train, you'll need the LONG track). I may end up adding the passenger train as that will extend the mod on the plastic which may help prevent the ball getting stuck in the plastic above the shooter lane etc.
BSoulMan BSoulMan The Pinboots accentuate the CE nicely... Nice and relatively inexpensive mod!
Harvester Harvester Simple products, easy install, nice peace of mind that doesn’t interfere with ball travel.
Harvester Harvester Installed the variant with “Death Eater”; built like a tank and going strong after 3 weeks and dozens of games.
MinusWorlds MinusWorlds Nice product. Fine feet faster seem solid, colors are great, and fit just right
Pintermission Pintermission Should have been stock for home use. I get that operators may love a fat left drain to keep game income higher, but nimr0d's left lane fix is the best mod for Star Wars in a home setting. Really helps remove frustration by making the left drain similar to right, especially with a geometry that can randomly autoplunge to the multiplier targets richoceting straight down left outlane without this fix. Order 2: one to install and one to keep as
a backup. Thanks so much!
bjorg bjorg Had another protector there before. It broke after a few plays. This one is robust and will probably outlast the pin itself!
bjorg bjorg Frankly, this is how the game should have looked from the get go. Super easy to install. Just cut the adhesive into small strips. Two screws to undo for the big ring. That's all there is to it. Super trivial!
bjorg bjorg Love it. Looks like it should have been there from the get go. I found it easier to loosen the screws behind the backboard and remove the mirror with its bracket. Then replace the mirror and reattach. Took me 15 minutes because I like to be careful. Probably one of the easiest mods to install!
bjorg bjorg The PinBoots match EXACTLY the color of the golden legs on the CE. It looks amazing! Highly recommended to pair with black leg levelers unless you can find golden ones. A must have for anyone who needs to protect their floors!
bjorg bjorg Yeah, this is so obvious. It should have been installed at the factory. Don't hesitate to buy! Every machine should have it.
DippinMyToeIn DippinMyToeIn This thing is pretty awesome! Lots of a attention to detail! It is larger than my other pincups, but not much larger. You won't be disappointed!
DippinMyToeIn DippinMyToeIn Easy and worthwhile mod. Should have been this way from the factory. A must for any HP pin.
M0st P0pular M0ds
Quidditch Golden Rings on Harry Potter Upper Playfield
Price range: $19.00 through $29.00
View Pr0duct
Previous
Next